Видео

I've used it. It's a short term fix, then fades away with the elements. Don't waste your money.

Every video I've seen on removing these make it look like it should just slip out... mine is stuck in the valve cover, lovely.

Hi. Im changing mine on a Peugeot boxer 270 camper 2000 soon.

best info video on you tube. Thank you from a professional.

I going to do it my by myself with this vid. Thanks

ABS plastic is black because carbon black is added. One part of ABS, is styrene, styrene is the weakest part of the formula. I doubt that the whuie areas most likely need to be dyed black.

Just an FYI to anyone doing this, COVER YOUR CAR PAINT if you are going to use higher speeds. Got this all over my mom’s car hood and it left a ton of micro scratches trying to wash it off!

How to replac an idle air control valve on 2011 vw jetta 2.0L

Great troubleshooting and video. Although, I have a 2004 Honda CRV with same problem, I will try that fuse and solenoid, if I can find the location.

NGK NOT NKG 😂😂

Freeze plug

You can also put a small piece of tape on the outside where the button goes. That is easy to remove than a crayon circle. Thanks for the video!

I did this and it worked. Not for other newbies like me, if you have thinner fabric use brush with lighter brisltes. Thanks for the info it really helped.

My shifter is stuck in park and my key has been stuck in the ignition for a week now. What could that be?

Bro thank you for this video! I have the same problem with the hood and here I thought I needed a special tool. Thanks again!!

Maybe you can show a video of how to change CVT transmission fluid, and Coolant cleaning/flushing. And changing the spark plugs, recommendations, etc.

Nice video. My wife has a 2017 Rogue SUV AWD. I’m new at this CVT engine. Maybe (in the near future) you can show a video of how to change CVT transmission fluid, and Coolant cleaning/flushing.

Thank you so much for making this video! I've used Meguiars PlastX on a light lens today where the transparent plastic was yellow instead of clear and it works exactly like you show in this video and it's very easy to work with too. I've polished by hand and the result is very good in my opinion after polishing the light lens multiple times. I'm definitely going to buy this product again!

Great video help me a lot and I didn’t think my car had one. Keep it up

Why you wasting that? wtf?

Having a simulator problem with my 2004 Mitsubishi endeavor ether it won't come out of park or won't go into park unless you fiddle with the shift linkage or turn off the car start it back up and it will go into park. haven't figured this one our yet but this video gave me some direction to possibly follow.

Did you know that most spark plugs come pre-gapped?.

Thank you, I had a timing belt,water pump replaced 1999 Toyota 4runner 3.4 the mechanic told me it was the oil pump. checked out your video and bingo. Thank you again,again

Thanks for video. i have already replaced the brake switch, and my scanner only detects the Purge valve canister, so i will try fuses next... 08 Ford Escape

Appreciate the video never done a Toyota before it looked straight forward but hey nothing wrong making sure you were gonna donit right

Thanks. I was wondering how to approach getting the mechanism out, I have found that it is the little plastic bushings on the handles that cause a large part of the problems. As soon as my window parts and door clips come in, I may try doing a video

Use a heat gun,it will make it look like new ,be cautious, keep it moving,just till it starts to change colour.

So what's that part called that you replaced ?

I'm told it's almost impossible to find an IACV for my 96 Honda Civic but two people in the know have said that's what I need.

" Here's your oral... oil dipstick tube" hahahaa. I have that car. It's great. Runs great no problems at all. Fiat did recall the cooling fan. The new part works wonderful.

My mirror thst is broken just has directional gadget inside to slant mirror. Mirror is cracked can I just remove broken mirror clean the backing plate while still attached wait till it dries than install new mirror over backing plate thst is still attached?

Where you strapping these ratchet straps to on other car?

Its a good tutorial video to restore the clarity and shine!! I've used this product in conjunction with a full 3M restoration kit on my badly degraded headlights, The only difference being after buffing with the PlastX i used Maguires clearcoat with added UV protection the best in my opinion, Also after care is most important for Derabilaty, Every time the car been washed i use Turtle wax headlight polish which as UV protection added, A clean micro fibre cloth a drop of polish rubbed on each lens and left for 5min's and buff by hand works wonders, My headlights still looks clear after 2years!!🤔😳🇬🇧👍

Very informative and concise video

thx 4 the video, knocking sounds r scary

What if the stainless steel button is still attached to window and the mirror has just detached itself?

What’s the horsepower?

Hey man that was a good segment right there

The metallic grey e36 looks like very pretty.

Hello, thank you for sharing valuable video. I am Ph.D student in university. I would like to use this video for my research. Could you permit me to use this video only for academic purpose? Thank you in advance.

You did this video 5 fkn yrs ago?!! It only took you 5 yrs ?!! Im on yra 10 and just finished by man handling 5he damn thing very strong addesive and a few minor self made clips 😂 seriously took me a damn hr maybe more measing with this thing,, long story short ....i assumed those2 plastic green arm rotating peices where press fit..didnt even think they come off thabks guy

Mines like that but mines is leaking

Sebastian Vettel's twin brother...nice job

Just changed mine last night. The previous two owners never did. I am confident I pulled out the original filter. The car 1995 318is has 208,899 miles.

I am replacing my iac valve on a 1996 Plymouth grand Voyager

And how do you get the other type of mirror button to work?

This was the perfect explanation for my experience today 👏 😊

All I did was take off the gas cap push my finger through that little metal piece that covers the gas line for a few seconds after no gas came out.

This really helped me with my v6 2001 Tundra

no gloves, no goggles.. good hes outside and uses a cardboard..